copyright © 2023 PT Global Sukses Digital
Offering lower noise, higher sensitivity, and more adjustable settings than the VideoMic, the Rode VideoMic Pro camera-mount shotgun microphone is ideal for mobile journalists, vloggers, budget filmmakers, and run-and-gun shooters looking for a cost-effective way to step up to the next level in quality.
A single 9V battery provides up to 70 hours of run time and an LED turns red to indicate low-battery status. Adjustable gain and a selectable bass roll-off make it easy to optimize the level and tone of your recording for a range of scenarios.
This compact and lightweight shotgun microphone features an integrated shockmount that mounts directly to your camera or boompole and reduces noise from various vibrations. The windscreen design reduces wind noise, making it well suited for outdoor shoots. The attached 3.5mm TRS cable ensures easy hookup to your camera, and the dual-mono output means that no channel selection is necessary on your recording device.
Whereas most built-in camera microphones pick up sound from all directions, this microphone utilizes a supercardioid polar pattern to focus on sound in front of it while attenuating sound from the sides and rear. Its low-noise electronics and sensitive condenser element deliver more detailed audio than the mics typically found in cameras and portable recorders.
A straight 3.5mm cable is permanently attached to the mic for fast hookup to your camera. The cable's 3.5mm TRS plug is wired in a dual-mono configuration, ensuring that the mic signal is sent identically to both input channels of your camera or portable recorder.
Pop a 9V battery in the VideoMic Pro for up to 70 hours of operating time. The dedicated power LED changes from green to red when the battery should be replaced. The VideoMic Pro can still function for approximately 10 hours once the power indicator turns red, but performance will be compromised. Use the power switch to conserve battery life during periods of inactivity.
The high-pass filter can be set to flat or 80 Hz to roll off low-frequency noise from common sources such as air conditioners and traffic.
To enable optimal recording levels, the VideoMic Pro boasts a 3-stage gain control. Like the low roll-off and high-frequency boost, the gain control is digitally switched for precision and convenience. The +20 dB setting is ideal when recording to cameras, as it boosts the signal without requiring extreme gain on the camera's inferior preamp. Select the flat setting when routing the mic into a dedicated high-quality preamp, or switch to the -10 dB option when loud sound sources threaten to distort your recording.
Understanding that the rubber bands used in many shockmounts can snap and stretch, Rode chose to integrate a rugged Rycote Lyre suspension-style shockmount. This simplifies setup of the mic and inhibits the transfer of vibrations from the camera. Plus, the bottom of the shockmount features a camera shoe mount with a 3/8" thread, ensuring easy attachment to your camera or a boompole such as Rode's Micro Boompole (available separately).
The VideoMic Pro has a foam windscreen to reduce unwanted wind noise from breezes, fans, heaters, and air conditioners. For maximum reduction of wind noise in outdoor environments, consider a furry windshield such as the Rode DeadCat VMPR (available separately).
Expand the microphone's device compatibility with Rode accessories such as the SC4 and VXLR (both available separately). The SC4 is a short cable that lets you connect the VideoMic Pro directly to a smartphone or tablet equipped with a 3.5mm TRRS jack. The VXLR adapter is the ideal solution when you want to record the VideoMic Pro to a camcorder or mixer that has XLR inputs.
Microphone
| Form Factor | Stand/Boom Mount |
| Sound Field | Mono |
| Operating Principle | Line Gradient |
| Capsule | Electret Condenser |
| Diaphragm | 0.5" / 12.70 mm |
| Polar Pattern | Supercardioid |
| Orientation | End Address |
| Circuitry | Solid-State (JFET) |
| Pad | None |
| High-Pass Filter | 80 Hz |
| Tone Adjustment | None |
| Gain Adjustment | -10 dB to +20 dB |
| Indicators | 1 x Single LED (Power) |
| On-Board Controls | Gain/Sensitivity, High-Pass Filter, On/Off |
| Windscreen | Foam (Included) |
Performance
| Frequency Range | 40 Hz to 20 kHz |
| Maximum SPL | 134 dB SPL |
| Off-Axis Rejection | 2 dB at 60° 18 dB at 120° 10 dB at 180° |
| Impedance | 200 Ohms |
| Sensitivity | -32 dBV/Pa at 1 kHz |
| Output Level | 6.9 dBu (Max) |
| Dynamic Range | 120 dB |
| Signal-to-Noise Ratio | 80 dB |
| Equivalent Noise Level | 14 dB A-Weighted |
Connectivity
| Output Connectors (Analog) | 1 x 1/8" / 3.5 mm TRS |
| Number of Conductors | 2 |
| Wireless Connectivity | None |
Power
| Operating Voltage | 9 V (Battery Power) |
| Operating Current Consumption | 7.8 mA |
| Battery Type | 1 x 9 V (Not Included) |
| Approximate Battery Life | 70 Hours |
Physical
| Color | Black |
| Mounting | Camera/Shoe-Mount, Shockmount (via Integrated Hardware) |
| Mounting Thread Size | 3/8"-16 Female |
| Included Case | None |
| Dimensions | ø: 3.94 x L: 6.69" / ø: 100 x L: 169.93 mm |
| Weight | 3 oz / 85 g |
Packaging Info
| Package Weight | 0.55 lb |
| Box Dimensions (LxWxH) | 8.6 x 5.15 x 3.1" |